

Wind Power -- Wind power is the conversion of wind energy into a useful form of energy, such as using wind turbines to make electricity, wind mills for mechanical power, wind pumps for pumping water or drainage, or sails to propel ships. At the end of 2009, worldwide nameplate capacity of wind-powered generators was 157.9 gigawatts which is about 1.5% of worldwide electricity usage and is growing rapidly, having doubled in the three years between 2005 and 2008. --- Several countries have achieved relatively high levels of wind power penetration such as 19% of stationary electricity production in Denmark, 13% in Spain and Portugal, 7% in Germany, and 7% in the Republic of Ireland in 2008. As of May 2009, eighty countries around the world are using wind power on a commercial basis. --- Utility companies increasingly buy back surplus electricity produced by small domestic turbines. Wind energy as a power source is attractive as an alternative to fossil fuels, because it is plentiful, renewable, widely distributed, clean, and produces no greenhouse gas emissions. The construction of wind farms has not been universally welcomed though because of the visual impact and other effects on the environment. --- Humans have been using wind power for at least 5,500 years to propel sailboats and sailing ships, and architects have used wind-driven natural ventilation in buildings since similarly ancient times. Windmills have been used for irrigation pumping and for milling grain since the 7th century AD. --- In the United States, the development of the water pumping windmills was the major factor in allowing the farming and ranching of vast areas otherwise devoid of readily accessible water. Wind pumps contributed to the expansion of rail transport systems throughout the world, by pumping water from water wells for the steam locomotives. The multi-bladed wind turbine atop a lattice tower made of wood or steel was, for many years, a fixture of the landscape throughout rural America. When fitted with generators and battery banks, small wind machines provided electricity to isolated farms. --- Small wind turbines for lighting of isolated rural buildings were widespread in the first part of the 20th century. Larger units intended for connection to a distribution network were tried at several locations including Balaklava USSR in 1931 and in a 1.25 megawatt experimental unit in Vermont in 1941. --- The modern wind power industry began in 1979 with the serial production of wind turbines by Danish manufacturers Kuriant, Vestas, Nordtank, and Bonus. These early turbines were small by today's standards, with capacities of 20–30 kW each. Since then, they have increased greatly in size, while wind turbine production has expanded to many countries. --- The Earth is unevenly heated by the sun, such that the poles receive less energy from the sun than the equator.In addition the dry land heats up and cools down more quickly than the seas do. The differential heating drives a global atmospheric convection system reaching from the Earth's surface to the stratosphere which acts as a virtual ceiling. Most of the energy stored in these wind movements can be found at high altitudes where continuous wind speeds of over 160 kmh/99 mph occur. Eventually, the wind energy is converted through friction into diffuse heat throughout the Earth's surface and the atmosphere. The total amount of economically extractable power available from the wind is considerably more than present human power use from all sources. An estimated 72 terawatts of wind power on the Earth potentially can be commercially viable compared to about 15 TW average global power consumption from all sources in 2005. Not all of the energy of the wind flowing past a given point can be recovered though. The strength of wind varies, and an average value for a given location does not alone indicate the amount of energy a wind turbine could produce there. To assess the frequency of wind speeds at a particular location, a probability distribution function is often fit to the observed data. Different locations will have different wind speed distributions. --- In a wind farm, individual turbines are interconnected with a medium voltage which is often a 34.5 kV power collection system and communications network. At a substation, this medium-voltage electrical current is increased in voltage with a transformer for connection to the high voltage electric power transmission system. The surplus power produced by domestic smaller generators can, in some areas, be fed into the network and sold to the utility company, producing a retail credit for the generators' owners to offset their energy costs. --- Different types of wind turbine generators behave differently during transmission grid disturbances, so extensive modeling of the dynamic electromechanical characteristics of a new wind farm is required by transmission system operators to ensure predictable stable behaviour during system faults --- Since wind speed is not constant, a wind farm's annual energy production is never as much as the sum of the generator nameplate ratings multiplied by the total hours in a year. The ratio of actual productivity in a year to this theoretical maximum is called the capacity factor. Typical capacity factors are 20–40%, with values at the upper end of the range in particularly favourable sites. For example, a 1 MW turbine with a capacity factor of 35% will not produce 8,760 MW·h in a year (1 × 24 × 365), but only 1 × 0.35 × 24 × 365 = 3,066 MW·h, averaging to 0.35 MW. Online data is available for some locations and the capacity factor can be calculated from the yearly output. --- Unlike fueled generating plants, the capacity factor is limited by the inherent properties of wind. Capacity factors of other types of power plant are based mostly on fuel cost, with a small amount of downtime for maintenance. Nuclear plants have low incremental fuel cost, and so are run at full output and achieve a 90% capacity factor. Plants with higher fuel cost are throttled back to follow load. Gas turbine plants using natural gas as fuel may be very expensive to operate and may be run only to meet peak power demand. A gas turbine plant may have an annual capacity factor of 5–25% due to relatively high energy production cost. --- Wind energy penetration refers to the fraction of energy produced by wind compared with the total available generation capacity. There is no generally accepted maximum level of wind penetration. The limit for a particular grid will depend on the existing generating plants, pricing mechanisms, capacity for storage or demand management, and other factors. An interconnected electricity grid will already include reserve generating and transmission capacity to allow for equipment failures; this reserve capacity can also serve to regulate for the varying power generation by wind plants. --- Studies have indicated that 20% of the total electrical energy consumption may be incorporated with minimal difficulty. --- At present, a few grid systems have penetration of wind energy above 5%: Denmark (values over 19%), Spain and Portugal (values over 11%), Germany and the Republic of Ireland (values over 6%). For instance, in the morning hours of 8 November 2009, wind energy produced covered more than half the electricity demand in Spain, setting a new record, and without problems for the network. The Danish grid is heavily interconnected to the European electrical grid, and it has solved grid management problems by exporting almost half of its wind power to Norway. The correlation between electricity export and wind power production is very strong. --- Electricity generated from wind power can be highly variable at several different timescales: from hour to hour, daily, and seasonally. Annual variation also exists, but is not as significant. Like other electricity sources, wind energy must be scheduled. Wind power forecasting methods are used, but predictability of wind plant output remains low for short-term operation. --- At low levels of wind penetration, fluctuations in load and allowance for failure of large generating units requires reserve capacity that can also regulate for variability of wind generation. Wind power can be replaced by other power stations during low wind periods. Transmission networks must already cope with outages of generation plant and daily changes in electrical demand. Systems with large wind capacity components may need more spinning reserve. --- In particular geographic regions, peak wind speeds may not coincide with peak demand for electrical power. In the US states of California and Texas, for example, hot days in summer may have low wind speed and high electrical demand due to air conditioning. Some utilities subsidize the purchase of geothermal heat pumps by their customers, to reduce electricity demand during the summer months, by making air conditioning up to 70% more efficient widespread adoption of this technology would better match electricity demand to wind availability in areas with hot summers and low summer winds. Another option is to interconnect widely dispersed geographic areas with an HVDC Super grid. --- In the USA it is estimated that to upgrade the transmission system to take in planned or potential renewables would cost at least $60 billion. Total annual US power consumption in 2006 was 4 thousand billion kW·hrs. --- In the UK, demand for electricity is higher in winter than in summer, and so are wind speeds. Solar power tends to be complementary to wind. On daily to weekly timescales, high pressure areas tend to bring clear skies and low surface winds, whereas low pressure areas tend to be windier and cloudier. On seasonal timescales, solar energy typically peaks in summer, whereas in many areas wind energy is lower in summer and higher in winter. --- Thus the intermittencies of wind and solar power tend to cancel each other somewhat. A demonstration project at the Massachusetts Maritime Academy shows the effect. The Institute for Solar Energy Supply Technology of the University of Kassel pilot-tested a combined power plant linking solar, wind, biogas and hydrostorage to provide load-following power around the clock, entirely from renewable sources. A report from Denmark noted that their wind power network was without power for 54 days during 2002. Wind power advocates argue that these periods of low wind can be dealt with by simply restarting existing power stations that have been held in readiness or interlinking with HVDC. Electrical grids with slow-responding thermal power plants and without ties to networks with hydroelectric generation may have to limit the use of wind power. Three reports on the wind variability in the UK issued in 2009, generally agree that variability of wind needs to be taken into account, but it does not make the grid unmanageable; and the additional costs, which are modest, can be quantified. Good selection of a wind turbine site is critical to economic development of wind power. Aside from the availability of wind itself, other factors include the availability of transmission lines, value of energy to be produced, cost of land acquisition, land use considerations, and environmental impact of construction and operations. Off-shore locations may offset their higher construction cost with higher annual load factors, thereby reducing cost of energy produced. --- Wind farm designers use specialized wind energy software applications to evaluate the impact of these issues on a given wind farm design. Wind power density is a calculation of the effective power of the wind at a particular location. A map showing the distribution of wind power density is a first step in identifying possible locations for wind turbines. --- There are 625,000 km2 in the contiguous United States that have class 3 or higher wind resources and which are within 10 km of electric transmission lines. If this area is fully utilized for wind power, it would produce power at the average continuous equivalent rate of 734 GWe. For comparison, in 2007 the US consumed electricity at an average rate of 474 GW, from a total generating capacity of 1,088 GW. World wind generation capacity more than quadrupled between 2000 and 2006, doubling about every three years. 81% of wind power installations are in the US and Europe. The share of the top five countries in terms of new installations fell from 71% in 2004 to 62% in 2006, but climbed to 73% by 2008 as those countries—the United States, Germany, Spain, China, and India—have seen substantial capacity growth in the past two years. By 2010, the World Wind Energy Association expects 160 GW of capacity to be installed worldwide, up from 73.9 GW at the end of 2006, implying an anticipated net growth rate of more than 21% per year. --- Denmark generates nearly one-fifth of its electricity with wind turbines—the highest percentage of any country—and is ninth in the world in total wind power generation. Denmark is prominent in the manufacturing and use of wind turbines, with a commitment made in the 1970s to eventually produce half of the country's power by wind. --- In recent years, the US has added more wind energy to its grid than any other country, with a growth in power capacity of 45% to 16.8 GW in 2007 and surpassing Germany's nameplate capacity in 2008. California was one of the incubators of the modern wind power industry, and led the U.S. in installed capacity for many years; however, by the end of 2006, Texas became the leading wind power state and continues to extend its lead. At the end of 2008, the state had 7,116 MW installed, which would have ranked it sixth in the world if Texas was a separate country. Iowa and Minnesota each grew to more than 1 GW installed by the end of 2007; in 2008 they were joined by Oregon, Washington, and Colorado. Wind power generation in the U.S. was up 31.8% in February, 2007 from February, 2006.The average output of one MW of wind power is equivalent to the average electricity consumption of about 250 American households. According to the American Wind Energy Association, wind will generate enough electricity in 2008 to power just over 1% (equivalent to 4.5 million households) of total electricity in U.S., up from less than 0.1% in 1999. U.S. Department of Energy studies have concluded wind harvested in the Great Plains states of Texas, Kansas, and North Dakota could provide enough electricity to power the entire nation, and that offshore wind farms could do the same job. --- In addition, the wind resource over and around the Great Lakes, recoverable with currently available technology, could by itself provide 80% as much power as the U.S. and Canada currently generate from non-renewable resources, with Michigan's share alone equating to one third of current U.S. electricity demand. China had originally set a generating target of 30,000 MW by 2020 from renewable energy sources, but reached 22,500 MW by end of 2009 and could easily surpass 30,000 MW by end of 2010. Indigenous wind power could generate up to 253,000 MW. A Chinese renewable energy law was adopted in November 2004, following the World Wind Energy Conference organized by the Chinese and the World Wind Energy Association. By 2008, wind power was growing faster in China than the government had planned, and indeed faster in percentage terms than in any other large country, having more than doubled each year since 2005. Policymakers doubled their wind power prediction for 2010, after the wind industry reached the original goal of 5 GW three years ahead of schedule. Current trends suggest an actual installed capacity near 20 GW by 2010, with China shortly thereafter pursuing the United States for the world wind power lead. India ranks 5th in the world with a total wind power capacity of 9,587 MW in 2008, or 3% of all electricity produced in India. The World Wind Energy Conference in New Delhi in November 2006 has given additional impetus to the Indian wind industry. Muppandal village in Tamil Nadu state, India, has several wind turbine farms in its vicinity, and is one of the major wind energy harnessing centres in India led by majors like Suzlon, Vestas, Micon among others. Mexico recently opened La Venta II wind power project as an important step in reducing Mexico's consumption of fossil fuels. The 88 MW project is the first of its kind in Mexico, and will provide 13 percent of the electricity needs of the state of Oaxaca. By 2012 the project will have a capacity of 3500 MW. Another growing market is Brazil, with a wind potential of 143 GW. The federal government has created an incentive program, called Proinfa, to build production capacity of 3300 MW of renewable energy for 2008, of which 1422 MW through wind energy. The program seeks to produce 10% of Brazilian electricity through renewable sources. South Africa has a proposed station situated on the West Coast north of the Olifants River mouth near the town of Koekenaap, east of Vredendal in the Western Cape province. The station is proposed to have a total output of 100 MW although there are negotiations to double this capacity. France has announced a target of 12,500 MW installed by 2010, though their installation trends over the past few years suggest they'll fall well short of their goal. Canada experienced rapid growth of wind capacity between 2000 and 2006, with total installed capacity increasing from 137 MW to 1,451 MW, and showing an annual growth rate of 38%. Particularly rapid growth was seen in 2006, with total capacity doubling from the 684 MW at end-2005. This growth was fed by measures including installation targets, economic incentives and political support. For example, the Ontario government announced that it will introduce a feed-in tariff for wind power, referred to as 'Standard Offer Contracts', which may boost the wind industry across the province. In Quebec, the provincially owned electric utility plans to purchase an additional 2000 MW by 2013. By 2025, Canada will reach its capacity of 55,000 MW of wind energy, or 20% of the country's energy needs. Due to ever increasing sizes of turbines which hit maximum power at lower speeds energy produced has been rising faster than nameplate power capacity. Energy more than doubled between 2006 and 2008 in the table above, yet nameplate capacity grew by 63% in the same period. --- Small-scale wind power is the name given to wind generation systems with the capacity to produce up to 50 kW of electrical power. Isolated communities, that may otherwise rely on diesel generators may use wind turbines to displace diesel fuel consumption. Individuals may purchase these systems to reduce or eliminate their dependence on grid electricity for economic or other reasons, or to reduce their carbon footprint. Wind turbines have been used for household electricity generation in conjunction with battery storage over many decades in remote areas. Grid-connected wind turbines may use grid energy storage, displacing purchased energy with local production when available. Off-grid system users can either adapt to intermittent power or use batteries, photovoltaic or diesel systems to supplement the wind turbine. In urban locations, where it is difficult to obtain predictable or large amounts of wind energy. Equipment such as parking meters or wireless Internet gateways may be powered by a wind turbine that charges a small battery, replacing the need for a connection to the power grid. --- Distributed generation from renewable resources is increasing as a consequence of the increased awareness of climate change. The electronic interfaces required to connect renewable generation units with the utility system can include additional functions, such as the active filtering to enhance the power quality. Wind power available in the atmosphere is much greater than current world energy consumption. The most comprehensive study found that as of 2005 found the potential of wind power on land and near-shore to be 72 TW, equivalent to 54,000 million tons of oil per year, or over five times the world's current energy use in all forms. The potential takes into account only locations with mean annual wind speeds ≥ 6.9 m/s at 80 m. The study assumes six 1.5 megawatt, 77 m diameter turbines per square kilometer on roughly 13% of the total global land area though that land would also be available for other compatible uses such as farming. The authors acknowledge that many practical barriers would need to be overcome to reach this theoretical capacity. --- The practical limit to exploitation of wind power will be set by economic and environmental factors, since the resource available is far larger than any practical means to develop it. --- A recent estimate gives the total potential average output for UK for various depth and distance from the coast. The maximum case considered was beyond 200 km from shore and in depths of 100 - 700 m, necessitating floating wind turbines, and this gave an average resource of 2,000 GWe which is to be compared with the average UK demand of about 40 GWe. Many potential sites for wind farms are far from demand centres, requiring substantially more money to construct new transmission lines and substations. In some regions this is partly because frequent strong winds themselves have discouraged dense human settlement in especially windy areas. The wind which was historically a nuisance is now becoming a valuable resource, but it may be far from large populations which developed in areas more sheltered from wind. --- Since the primary cost of producing wind energy is construction and there are no fuel costs, the average cost of wind energy per unit of production depends on a few key assumptions, such as the cost of capital and years of assumed service. The marginal cost of wind energy once a plant is constructed is usually less than 1 cent per kW·h. Since the cost of capital plays a large part in projected cost, risk will affect projected costs per unit of electricity. The commercial viability of wind power also depends on the price paid to power producers. Electricity prices are highly regulated worldwide, and in many locations may not reflect the full cost of production. Customers may enter into long-term pricing contracts for wind to reduce the risk of future pricing changes, thereby ensuring more stable returns for projects at the development stage. These may take the form of standard offer contracts, whereby the system operator undertakes to purchase power from wind at a fixed price for a certain period; these prices may be different than purchase prices from other sources, and even incorporate an implicit subsidy. --- Where the price for electricity is based on market mechanisms, revenue for all producers per unit is higher when their production coincides with periods of higher prices. The profitability of wind farms will therefore be higher if their production schedule coincides with these periods. If wind represents a significant portion of supply, average revenue per unit of production may be lower as more expensive and less-efficient forms of generation, which typically set revenue levels, are displaced from economic dispatch. This may be of particular concern if the output of many wind plants in a market have strong temporal correlation. In economic terms, the marginal revenue of the wind sector as penetration increases may diminish. --- For electric production, the most significant concern is pollution, which imposes social costs in increased health expenses, reduced agricultural productivity, and other problems. In addition, carbon dioxide, a greenhouse gas produced when fossil fuels are burned, may impose even greater costs in the form of global warming. Few mechanisms currently exist to internalise these costs, and the total cost is highly uncertain. --- If the external costs are taken into account, wind energy can be competitive in more cases, as costs have generally decreased because of technology development and scale enlargement. Supporters argue that, once external costs and subsidies to other forms of electrical production are accounted for, wind energy is amongst the least costly forms of electrical production. There are over 6,000 wind turbines at Altamont Pass, in California, United States. Developed during a period of tax incentives in the 1980s, this wind farm has more turbines than any other in the United States. --- Countries such as Canada and Germany also provide incentives for wind turbine construction, such as tax credits or minimum purchase prices for wind generation, with assured grid access, sometimes referred to as feed-in tariffs. These feed-in tariffs are typically set well above average electricity prices. The Energy Improvement and Extension Act of 2008 contains extensions of credits for wind, including microturbines. Secondary market forces also provide incentives for businesses to use wind-generated power, even if there is a premium price for the electricity. For example, socially responsible manufacturers pay utility companies a premium that goes to subsidize and build new wind power infrastructure. --- Companies use wind-generated power, and in return they can claim that they are making a powerful 'green' effort. In the USA the organization Green-e monitors business compliance with these renewable energy credits. For those with an economic interest in capturing as much of the climate-change pork barrel as possible, there are two ways of presenting the costs in a favourable light: first, define the cost base as narrowly as possible; and, second, assume that the costs will fall over time with R&D and large-scale deployment. --- Compared to the environmental effects of traditional energy sources, the environmental effects of wind power are relatively minor. Wind power consumes no fuel, and emits no air pollution, unlike fossil fuel power sources.
turbine jet skyscraper wind motor sport latest bullet legal passenger auto two wheels red swiss white street precision lightning German training wheeler touch maskus sleek
![]() |
| wind |
